Gw-instek PEL-2000 Series Programming User Manual Bedienungsanleitung Seite 140
- Seite / 170
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
PEL-2000 Programming Manual
140
Query Example
:POWer:HIGH:BVAL? AX
2
Returns the maximum
power allowed for the
channel/range.
:POWer:HIGH:CURRent
Channel Specific
Command
Description
Sets the current limit for constant power mode for
the high range only.
Syntax
:POWer:HIGH:CURRent <NRf+>[A]
Parameter
<NRf+>[A]
1
Sets the current limit to
1A.
1A
Sets the current limit to
1A.
MIN
Sets the current limit to
the minimum level for the
specific channel.
MAX
Sets the current limit to
the maximum level for the
specific channel.
Example
:POW:HIGH:CURR 1
Sets the current limit to
1A.
Query Syntax
:POW:HIGH:CURRent? [MAX|MIN]
Return Parameter
<NR2> [MAX|MIN]
Current
1 unit = 1 amp
Returns the current limit.
MAX/MIN
Returns the allowable
maximum and minimum.
Query Example
:POW:HIGH:CURR?
7.0
Returns the current limit
for the specific channel.
- PEL-2000 Series 1
- PROGRAMMING MANUAL 1
- Table of Contents 3
- INTERFACE OVERVIEW 5
- Interface 6
- GPIB Interface Configuration 11
- COMMAND OVERVIEW 13
- FETCh:VOLTage? 14
- COMMAND OVERVIEW 23
- Global 23
- COMMAND DETAILS 24
- COMMAND DETAILS 25
- Common commands 26
- Manufacturer 28
- Abort Subsystem 32
- Channel Subsystem 33
- :CHANnel:ACTive 34
- :CHANnel:SYNCon 34
- :CHANnel:SYNCon:ALL 35
- :CHANnel:ID? 35
- :CHANnel:DISPlay 35
- :CHANnel:MEMo 36
- CONFIGURE Subsystem 38
- :CONFigure:VOLTage:RANGe 39
- :CONFigure:VOLTage:LATch 40
- :CONFigure:AUTO:LOAD 40
- :CONFigure:AUTO:MODE 41
- :CONFigure:SOUND 41
- :CONFigure:SAVE 42
- :CONFigure:LOAD 42
- :CONFigure:REMote 42
- :CONF:PROT:CURR:STAT 1 43
- :CONF:PROT:CURR:STAT? 43
- :CONFigure:RESPonse 48
- :CONFigure:RESEt 49
- :CONFigure:GROup:UNITs 49
- :CONFigure:GROup:MODE 50
- Utility Subsystem 51
- :UTILity:AUTO:MODE 52
- :UTILity:SOUNd 52
- :UTILity:REMote 53
- :UTILity:REMote:MODE 53
- :UTILity:IDENtify 55
- :UTILity:FRAMe 55
- Current Subsystem 56
- :CURRent:STATic:L1/L2 57
- :CURRent:STATic:RISE/FALL 58
- :CURR:STAT:LOW:RISE .001 60
- :CURRent:DYNamic:L1/L2 62
- :CURRent:DYNamic:RISE/FALL 63
- :CURRent:DYNamic:T1/T2 64
- :CURRent:DYNamic:LOW:L1/L2 65
- :CURRent:DYNamic:LOW:T1/T2 67
- :CURRent:DYNamic:HIGH:L1/L2 67
- :CURRent:DYNamic:HIGH:T1/T2 69
- FETCH Subsystem 71
- :FETCh:POWer? 72
- :FETCh:STATus? 72
- :FETCh:ALLVoltage? 72
- :FETCh:ALLCurrent? 73
- :FETCh:ALLPower? 73
- LOAD Subsystem 75
- :LOAD:SHORt:KEY 76
- :LOAD:PROTection? 76
- :LOAD:PROTection:CLEar 77
- :LOAD:TIME? 77
- :LOAD:DELay 78
- :LOAD:TYPE 78
- Measure Subsystem 80
- :MEASure:POWer? 81
- :MEASure:INPut 81
- :MEASure:SCAN 82
- :MEASure:ALLVoltage? 82
- :MEASure:ALLCurrent? 83
- :MEASure:ALLPower? 83
- MODE Subsystem 85
- OCP Test Automation Commands 87
- :OCP:CHANnel:RANGe 88
- :OCP:CHANnel:STARt 88
- :OCP:CHANnel:END 89
- :OCP:CHANnel:STEP:CURRent 89
- :OCP:CHANnel:LAST 90
- :OCP:CHANnel:STEP:TIME 90
- :OCP:CHANnel:DELay 91
- :OCP:CHANnel:TRIGger 91
- :OCP:CHANnel:ACTive 92
- :OCP:STATus? 92
- :OCP:SAVE 93
- :OCP:RESult? 93
- :OCP:RUN 93
- Program Subsystem 94
- :PROGram:SEQuence 95
- :PROGram:MEMory 95
- (BIT WEIGHT) 96
- :PROGram:SEQuence:SHORt:TIME 97
- :PROGram:SEQuence:MODE 97
- :PROGram:ACTive 98
- :PROGram:CHAin 99
- :PROGram:ONTime 99
- :PROGram:OFFTime 100
- :PROGram:RUN 101
- :PROGram:SAVE 101
- :PROGram:PFTime 101
- :PROGram:CHAin:STARt 102
- Resistance Subsystem 103
- :RESistance:STATic:RECall 105
- RUN Subsystem 115
- SHOW Subsystem 116
- SPECIFICATION Subsystem 118
- :SPECification:TEST: 121
- STATUS Subsystem 122
- :STATus:CHANnel:ENABle 123
- :STATus:CHANnel:EVENt? 123
- :STATus:CHANnel:NTRansition/ 124
- PTRansition 124
- :STATus:CSUMmary:ENABle 125
- :STATus:CSUMmary:EVENt? 126
- :STATus:QUEStionable:ENABle 127
- :STATus:PREset 129
- Voltage Subsystem 130
- :VOLTage:RECall 131
- :VOLTage:AVALue/BVALue 131
- :VOLTage:CURRent 132
- :VOLTage:MODE 133
- Power Subsystem 135
- :POWer:CURRent 136
- :POWer:RECall 137
- :POWer:LOW:AVALue/BVALue 137
- :POWer:LOW:CURRent 138
- :POWer:HIGH:AVALue/BVALue 139
- :POWer:HIGH:CURRent 140
- SYSTEM Subsystem 141
- :SYSTem:SETup 142
- Memory Subsystem 143
- :MEMory:SAVE:ALLPreset 144
- :MEMory:SAVE:SETup 144
- :MEMory:RECall:PREset 144
- :MEMory:RECall:PROGram 145
- :MEMory:RECall:ALLPreset 145
- :MEMory:RECall:SETup 145
- :MEMory:FILE:PRESet 146
- :MEMory:FILE:PROGram 146
- :MEMory:FILE:SETup 147
- :MEMory:FILE:SEQuence 147
- SEQuence Subsystem 149
- :SEQuence:END 150
- :SEQuence:POINt:RESistance 150
- :SEQuence:POINt:CURRent 151
- :SEQuence:POINt:RISE/FALL 151
- :SEQuence:REPeat 153
- :SEQuence:END:LOAD 153
- :SEQuence:VOLTage:RANGe 154
- :SEQuence:LOOP:STARt 155
- :SEQuence:CHANnel:TIME 155
- :SEQuence:RUN 156
- :SEQuence:SAVE 156
- :SEQuence:TRIGger:IN 156
- :SEQuence:TRIGger:OUT 157
- :SEQuence:TRIGger:IN:CHANnel 157
- GLOBal Subsystem 159
- Command Error Codes 161
- STATUS REGISTERS 162
- STATUS REGISTERS 163
- Channel Status 164
- Channel Summary 165
- Questionable Status 166
- Output Queue 167
- Data inData out 167
- Standard Event Status 168
- Status Byte Register 169
- Service Request Register 170
Verwandte Produkte und Handbücher für Ausrüstung Gw-instek PEL-2000 Series Programming User Manual
Ausrüstung Gw-instek PPH-1503 Bedienungsanleitung
(137 Seiten)
(137 Seiten)
Ausrüstung Gw-instek LCR-914 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern