Gw-instek PEL-3000 Series Programming Manual Bedienungsanleitung PDF herunterladen (Seite 161)

COMMNAND OVERVIEW

159

Service Request Register

Overview

The Service Request Generation Register

determines which events in the Status Byte

essentially the Status Byte Enable Register. The

bit events are the same as the Status Byte

Service Request Generation Register (Status Byte Enable)

QUES CSUM ERR 0

128

OPER 0 ESB MAV

Bit weight

Bit Position

Condition

1 2 ... 156 157 158 159 160 161 162 163 164 165 166 ... 173 174

DC Electronic Load 1
Table of Contents 3
INTERFACE OVERVIEW 4
Front Panel Overview 5
Rear Panel Overview 6
Interface Configuration 7
Configure GPIB Interface 8
1 2 3 4 5 9
GPIB Function Check 15
INTERFACE OVERVIEW 17
COMMNAND OVERVIEW 18
:CURRent:Set 21
Command List 23
:CURRent[:VA]:TRIGgered 37
:RESistance[:VA]:TRIGgered 37
Example 38
:RESistance:TRIGgered MAX 38
:INPut:MODE 40
:MEASure:ETIMe? 42
Configure Subsystem Commands 43
[:CONFigure]:OCP 43
[:CONFigure]:OPP 44
[:CONFigure]:SSTart 46
[:CONFigure]:COTime 49
[:CONFigure]:GNG:C 55
Parallel Commands 56
[:CONFigure]:PARallel 56
Step Resolution Commands 58
[:CONFigure]:STEP:CCH 58
[:CONFigure]:STEP:CC 60
[:CONFigure]:STEP:CRH 60
[:CONFigure]:STEP:CRM 61
[:CONFigure]:STEP:CRL 62
[:CONFigure]:STEP:CR 62
[:CONFigure]:STEP:CV 64
[:CONFigure]:STEP:CPH 64
[:CONFigure]:STEP:CP 66
[:MODE]:DYNamic 71
Current Subsystem Commands 72
:CURRent[:VA] 72
:CURRent:SET 75
:CURRent:T2 78
:RESistance[:VA] 81
:RESistance:L1 83
:RESistance:LEVel 85
:RESistance:T1 87
:RESistance:DUTY 89
Power Subsystem Commands 93
:POWer[:VA] 93
:POWer:LEVel 96
:POWer:FREQuency 98
:POWer:DUTY 99
Function Commands 100
:PROGram:STATe 101
:PROGram 102
:PROGram[:RECall]:DEFault 103
:PROGram:STARt 103
[:PROGram]:CHAin:P2P 109
:PROGram:SAVE 110
:NSEQuence:STATe 110
:NSEQuence 111
:NSEQuence:STARt 112
:NSEQuence:EDIT 117
:NSEQuence:EDIT:POINt 118
:FSEQuence 120
:FSEQuence:MEMO 121
:FSEQuence:EDIT:POINt 126
:FSEQuence:SAVE 128
:UTILity:LOAD:MODE 130
:UTILity:LOAD:RANGe 131
SCPI Register Commands 142
:SYSTem:ERRor? 142
:STATus:PRESet 143
:STATus:CSUMmary:PTRansition 151
Status Registers 153
CSummary Status Registers 155
Questionable Status Register 156
Operation Status Registers 157
Status Byte Register 160
Service Request Register 161
Error Messages 162

Kommentare zu diesen Handbüchern

Keine Kommentare

Gw-instek PEL-3000 Series Programming Manual Bedienungsanleitung Seite 161

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Gw-instek PEL-3000 Series Programming Manual